How can I test if my heating element is bad?

You can test a heating element for continuity using a multimeter. Disconnect power, remove the element, and set your multimeter to the ohms setting. Touch the probes to the element's terminals. A reading of infinity or no continuity indicates a broken element.

What causes a dryer heating element to fail?

Common causes include normal wear and tear over time, lint buildup restricting airflow and causing overheating, or a faulty thermal fuse or thermostat allowing the element to overheat. Overloading the dryer can also contribute to premature failure.

Can I replace a heating element myself?

Yes, replacing a dryer heating element is a common DIY repair for those with basic tool knowledge. Always ensure the dryer is unplugged before starting any work to prevent electrical shock. Refer to your appliance's specific service manual for detailed instructions.

Dryer Heating Element Replacement Guide

Appliance Aid takes part in the Amazon Associates programme. Some links on this page are affiliate links, and a qualifying purchase earns us a commission. Your price is unchanged.

🏆 RECOMMENDED PART

AZ4U 134792700 Dryer Heating Element For Frigidaire, Electrolux Dryer

Package include: 1x Dryer Heating Element, 1x Thermal Fuse, 1x High Limit Thermostat ( all 3 pcs as the picture). Compatibility : this is aftermarket part replace For Frigidaire, Electrolux, Kenmore, Crosley electric ...
Parts Compatibility: Dryer Heating Element 134792700, 1482984, 7134792700; Thermal Fuse 137032600, 137060800, 7137032600; High Limit Thermostat 3204267, 508516, 73204267.
Fit for model : FASE7021NW0 FASE7021NW2 FASE7021NW3 FASE7073LA0 FASE7073LN0 FASE7073LR0 FASE7073LW0 FASE7073NA0 FASE7073NA2 FASE7073NA3 FASE7073NR0 FASE7073NR2 FASE7073NR3 FASE7073NW0 FASE7073NW2 FASE7073NW3 FASE7074L...
✔️ Related Key Words : for electrolux 134792700 heater, for electrolux dryer heating element 134792700, dryer part 134792700, for electrolux dryer part 134792700, for electrolux heating element 134792700, part number ...
✔️ Related Key Words : heating element part number 134792700, ap4368653 element, frigidaire affinity dryer element, frigidaire affinity dryer heating element, 134792700-137032600-3204267-thermostat-frigi-daire, 134792...

Check Price on Amazon

What the FASE7073LR0 does

The heating element generates the heat necessary to dry clothes in an electric dryer. It converts electrical energy into thermal energy.

Symptoms when this part fails

Dryer runs but clothes remain wet
Dryer takes much longer than usual to dry clothes
No heat or insufficient heat during a cycle
Dryer trips the circuit breaker

Compatibility

Fits the Frigidaire family. Specifically:

Any unit originally equipped with OEM part number(s): 134792700, AP4368653, FASE7073LW0.
Check the model/rating plate inside your appliance and compare it against the fitment table on the product listing before ordering — this guide does not list specific compatible models because Amazon does not provide verified fitment data through this pipeline.

Also replaces: 134792700, AP4368653, FASE7073LW0

Tools you'll need

Screwdriver (Phillips and/or flathead)
Nut driver set
Pliers
Multimeter (for testing)

Difficulty: Moderate · Time: 30-60 minutes

How to install the FASE7073LR0, step by step

Unplug the dryer from its power source.
Disconnect the dryer vent hose.
Remove the rear access panel screws.
Locate the heating element assembly.
Disconnect wires and mounting screws from the old element.
Install the new heating element and reconnect wires.
Reattach the access panel and vent hose.
Restore power and test the dryer.

Related troubleshooting

If swapping this part doesn't fix the issue, check these next:

Dryer not heating up but runs? 6 fixes for Whirlpool, Samsung, LG, GE and more