How do I know if my water inlet valve is bad?

Common signs include the dishwasher not filling with water, overflowing, or a loud buzzing sound during the fill cycle. Leaks near the valve area or insufficient water levels can also indicate failure of the part. If the dishwasher is not getting water, or too much water, the inlet valve is a likely suspect.

Where is the water inlet valve located on a dishwasher?

The water inlet valve is typically found at the bottom front or side of the dishwasher, behind the lower access panel. It connects directly to the household water supply line and has an electrical connection to the dishwasher's control system.

Can I clean a dishwasher water inlet valve instead of replacing it?

While some valves have a small filter screen that can be cleaned, the internal mechanisms of a water inlet valve are generally not repairable. If the valve is failing to open or close properly, or if it is leaking, replacement is usually the recommended solution rather than attempting a repair.

Dishwasher Water Inlet Valve Replacement Guide

Appliance Aid takes part in the Amazon Associates programme. Some links on this page are affiliate links, and a qualifying purchase earns us a commission. Your price is unchanged.

🏆 RECOMMENDED PART

WD15X27703 Dishwasher Water Valve Assembly for GE, Hotpoint GDF535PSR3SS

Product function: WD15X32008 dishwasher inlet valve is designed to replace the broken or damaged valve and ensure a steady water flow. It solves dishwasher water supply issues, including low water flow and leaks. Manu...
Product specification: WD15X27703 dishwasher water valve assembly is made of materials, rated at 120V, 60Hz, and meets the standards for manufacturing
Part Number: WD15X27703 dishwasher water valve assembly Can be replaced WD15X32008 , 265D3719G002 , 4964202 , AP6994873 , PS16219694 , EAP16219694
Compatible Mode： compatible with ge dishwasher : GDT670SYV1FS; GDF535PSR0SS; GDT550PYR3FS; GDF510PSR0SS; GDT630PGR7BB; GDF511PSR5SS; GDT630PYR6FS; GDF550PSR3SS; GDT670SYV0FS; GDF460PGT3WW; GDT550PYR7FS; GDF535PSR3SS; ...
Installation Note: Before replacing the WD15X27703 dishwasher water inlet valve, verify the dishwasher model and original part number to confirm compatibility. Disconnect the power and water supply before installation

Check Price on Amazon

What the WD15X27703 does

The water inlet valve controls the flow of water into the dishwasher tub at specific points in the wash cycle. It opens to allow water in and closes to stop the flow.

Symptoms when this part fails

Dishwasher not filling with water
Dishwasher overflowing
Loud buzzing noise during fill cycle
Leaking from the bottom of the dishwasher
Inadequate water level in the tub

Compatibility

Fits the GE family. Specifically:

Any unit originally equipped with OEM part number(s): WD15X27703.
Check the model/rating plate inside your appliance and compare it against the fitment table on the product listing before ordering — this guide does not list specific compatible models because Amazon does not provide verified fitment data through this pipeline.

Tools you'll need

Pliers
Screwdriver (Phillips/Flathead)
Adjustable wrench
Towels/rags

Difficulty: Moderate · Time: 30-60 minutes

How to install the WD15X27703, step by step

Disconnect power and water supply to the dishwasher.
Remove the lower access panel beneath the dishwasher door.
Locate the water inlet valve, typically on the left or right side.
Disconnect the water supply line and electrical connections from the valve.
Disconnect the internal hose from the valve to the dishwasher tub.
Remove mounting screws and detach the old valve.
Install the new valve, reconnecting all hoses, electrical, and mounting screws.
Restore power and water, then check for leaks before replacing the access panel.