How do I know if my water inlet valve is bad?

Common signs of a faulty valve include the washer not filling, filling too slowly, or continuously filling and overflowing. You might also hear a constant humming sound or notice leaks near the valve connections at the back of the machine.

Can I clean a water inlet valve instead of replacing it?

While some valves have screens that can be cleaned to remove sediment, the internal mechanisms are typically not serviceable. If the valve itself is faulty due to solenoid or seal issues, replacement is usually the only effective solution.

What causes a water inlet valve to fail?

Over time, wear and tear, mineral deposits from hard water, or electrical issues can cause the solenoids or seals within the valve to fail. Extreme water pressure fluctuations or sediment buildup can also contribute to damage.

Washing Machine Water Inlet Valve Replacement

Appliance Aid takes part in the Amazon Associates programme. Some links on this page are affiliate links, and a qualifying purchase earns us a commission. Your price is unchanged.

🏆 RECOMMENDED PART

Upgraded W10144820 Washer Water Inlet Valve Compatible with whirlpool amana kenmore Washers,Replace AP6015761, W10140914, WPW10144820,W10311

[W10144820 Replaces Part Numbers] : WPW10144820,W10311458, W1AP6015761, PS11749042, EAP11749042, W10140914, W10140911, AP4371093, PS2347919, W10311458, PS11749042 etc.
[Wide Compatibility]: W10144820 Washer Valve Compatible With whirlpool, maytag, kenmore, roper, crosley, estate, amana, admiral, Inglis etc .
[Fixable Symptoms]:It mainly solves the problems of water leakage, short circuit, imbalance of hot and cold water, inaccurate water level and loud noise. When your washer is slow to fill, noisy, overflowing or stopped...
[Washer Water Inlet Valve]: The w10144820 water inlet valve includes red hot water valve, blue cold water valve, vacuum break and thermistor sensor for sensing water temperature, w10144820 washer water inlet valve has...
[Customer Satisfaction Guaranteed]:Please refer to the picture for product size and fit model information, before your order. If you cannot ensure that it fits your washing machine. Feel free to contact us anytime.PLE...

Check Price on Amazon

What the W10144820 does

The water inlet valve controls the flow of hot and cold water into the washing machine tub during various cycles. It opens and closes based on electrical signals from the washer's control board.

Symptoms when this part fails

Washer not filling with water
Washer filling slowly or intermittently
Washer overflowing or continuously filling
Water leaking from the rear of the washer
Washer making a humming noise but not filling

Compatibility

Fits the Kenmore family. Specifically:

Any unit originally equipped with OEM part number(s): AP6015761, W10140914, WPW10144820, W10311458, W1AP6015761, PS11749042.
Check the model/rating plate inside your appliance and compare it against the fitment table on the product listing before ordering — this guide does not list specific compatible models because Amazon does not provide verified fitment data through this pipeline.

Also replaces: AP6015761, W10140914, WPW10144820, W10311458, W1AP6015761, PS11749042

Tools you'll need

Pliers
Screwdriver (Phillips and flathead)
Nut driver
Bucket
Towels

Difficulty: Moderate · Time: 30-60 minutes

How to install the W10144820, step by step

Disconnect power and turn off the hot and cold water supply to the washer.
Pull the washer away from the wall to access the rear panel.
Remove the screws securing the rear access panel and set it aside.
Disconnect the electrical connectors and water hoses from the old valve.
Remove the mounting screws or clips holding the valve in place.
Install the new water inlet valve, ensuring all connections are secure.
Reattach the rear panel, reconnect power, and turn on the water supply.
Test the washer for proper operation and check for leaks.

Related troubleshooting

If swapping this part doesn't fix the issue, check these next:

Washing Machine Fills With Water Then Stops? 7 Fixes